Step 6: Check your settings again before saving. Page Network Settings After everything is done, system would reboot automatically. Please wait 30 seconds at least for system restarting. Page Dhcp Setting You can change it if necessary. Page 46 Following information will let you know the current wireless operation status.
Basic Settings: allow you to enable or disable wireless function. Please refer to the following section to check details of each wireless mode separately. Page 47 AP Setting: Channel: choose the radio channel number. Page 48 the authentication method for various encryption schemes. This device only supports WPA version 1. Please refer to FAQ in chapter 7 to get more detailed information. Then click the AP that you want to connect to. Page 52 Input encryption keys if needed.
The encryption method is decided by remote AP. After that, you can check the wireless status in the status page. Besides selecting AP from available list, you can also add AP manually.
You may also need to input correct encryption keys when remote AP activates encryption mechanism. Page 56 You can also modify attributes of existed AP. Page 58 3. The wireless channel must be same as remote AP. Please refer to 3.
Page 65 Finally, you could see the confirm page. Page 66 3. Page 71 Finally, you could see the confirm page. Page Chapter 4: Disk Management Besides, this chapter will also show you how to finish configurations of File Sharing, and assign user access rules. Advanced Settings In the advanced settings, two more options will be shown Page 74 The first option is used for disk checking.
Page File Sharing 4. User Access Configuration If you set security level to Guest only, everyone can access data which is stored in the hard disk. If you change option to Authorization User, only authorized users have permission to access. Page 79 Then you could see sub-directories of folder C, select Read. Then you can find there is a new shared directory in the list. Besides, you can also set the maximum connections of FTP that are allowed at the same time.
Page Chapter 5: Advanced Tools Refer to the following sections for more details. Once you want to restore these settings, please click the Firmware Upgrade option and use the bin file you saved.
Page Reset Configuration To Default 5. Page Chapter 6: Misc 6. The System Time provides two options for you to select. Page Change Password 6. EZ Installation W izar d.
IEEE Supports major Windo ws oper ating syst ems. Ad-hoc or Infr astructure mode. WP A , Ability t o define multiple Pro file set tings. EZ Installation W izar d ensure s simple and eas y setup o f the new. Back w ar d compatibilit y to e xisting It also incr eases the r ange and provide s ext ended cover age in your. The VPN protocols supported by the Barricade are briefly described below.
IPSec can support large encryption networks such as the Internet by using digital certificates for device authentication. Also be sure that you have all the necessary cabling before installing the Barricade. After unpacking the Barricade, check the contents of the box to be sure you have received the following components:. Immediately inform your dealer in the event of any incorrect, missing, or damaged parts.
If possible, please retain the carton and original packing materials in case there is a need to return the product. Access speed to the Internet depends on your service type. However, you should note that the actual rate provided by specific service providers may vary dramatically from these upper limits.
Data passing between devices connected to your local area network can run at up to Mbps over the Fast Ethernet port and 54 Mbps over the built-in wireless network adapter. The Barricade includes an LED display on the front panel for system power and port indications that simplifies installation and network troubleshooting. The power and port LED indicators on the front panel are illustrated by the following table. Warning : Using the wrong type of power adapter may cause.
Please collect the following information from your ISP before setting up the Barricade:. The Barricade can be positioned on any convenient flat surface in your office or home. No special wiring or cooling requirements are needed. You should, however, comply with the following guidelines:. You should also remember to turn off the power, remove the power cord from the outlet, and keep your hands dry when you install the Barricade. There are two wall-mount holes at the bottom of the Barricade.
Before drilling two holes into the wall, make sure the holes are mm apart. Choose a suitable location for the Barricade. Note: It should be accessible for installing, cabling and maintaining the device. Measure the distance of the two wall-mount holes.
Drill two holes into the wall. Insert a screw into each hole. Attach the Barricade to the wall with two wall-mount slots, and then slide the device down until the screws fit firmly into the slots of the device. The four LAN ports on the Barricade auto-negotiate the connection speed to 10 Mbps Ethernet or Mbps Fast Ethernet, as well as the transmission mode to half duplex or full duplex.
Otherwise, cascade any of the LAN ports on the Barricade to an Ethernet hub or switch, and then connect your PC or other network equipment to the hub or switch. When inserting an RJ connector, be sure the tab on the connector clicks into position to ensure that it is properly seated.
Warning: Do not plug a phone jack connector into an RJ port. This may damage the Barricade. Notes: 1. Use ohm shielded or unshielded twisted-pair cable with RJ45 connectors for all Ethernet ports. Use Category 3, 4, or 5 for connections that operate at 10 Mbps, and Category 5 for connections that operate at Mbps. Make sure each twisted-pair cable length does not exceed meters feet.
Plug the power adapter into the power socket on the side panel of the Barricade, and the other end into a power outlet. Check the power indicator on the front panel is lit.
In case of a power input failure, the Barricade will automatically restart and begin to operate once the input power is restored. If the Barricade is properly configured, it will take about 30 seconds to establish a connection with the ADSL service provider after powering up. After completing hardware setup by connecting all your network devices, you need to configure your computer to connect to the Barricade.
To access the Internet through the Barricade, you must configure the network settings of the computers on your LAN to use the same IP subnet as the Barricade. The default network settings for the Barricade are:. Click the icon that corresponds to the connection to your Barricade. The connection status screen will open. If Obtain an IP address automatically and Obtain. If not, select these options now and click OK. Now that you have configured your computer to connect to your Barricade, it needs to obtain new network settings.
By releasing old DHCP IP settings and renewing them with settings from your Barricade, you can verify that you have configured your computer correctly. Verify that your IP Address is now These values confirm that your Barricade is functioning correctly. Enter an IP address based on the default network Record the configured information in the following table. To disable the proxy in Internet Explorer, click. Click Internet Options Locate and double-click the Local Area Connection icon for the Ethernet adapter that is connected to the Barricade.
In the connection status screen, click Properties. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password.
0コメント